LS Fishing

Accessories for your bait boat and underwater camera.

Designed by a carp angler, measured for each model and tested at the water. Made to fit the Carplounge RT4 and RT7, the AIO controller and the Winchcam from Carplounge and Stealthcam UK.

View on Etsy All products
The Carplounge AIO controller on a tripod by the lake, with the Winchcam monitor in the holder above it and the bait boat on the water

Products

For carp anglers with a Carplounge bait boat: a holder for your monitor, an anti-spin for your underwater camera and parts for the RT4 and RT7.

Monitor holder for the Carplounge AIO controller

Your monitor on your controller. No more loose screen on your knee or on a bank stick while you steer the bait boat. The holder clips onto the Carplounge AIO controller and puts the monitor of your underwater camera right above your hands, tilted 15 degrees towards you. Controller and monitor stay together as one unit.

  • Clips over the top and bottom edge of the controller, without drilling, screws or tape
  • The monitor clips in and is easy to take out again
  • Antennas, connectors and the tripod mount stay clear
  • Screen holder and frame clip together: change monitor, keep the same frame
Carplounge Winchcam
7-inch monitor with sun hood
Stealthcam UK Winchcam
5-inch monitor

Also available as a set with a matching anti-spin for the same camera.

Monitor holder on Etsy
The 5-inch monitor of the Stealthcam Winchcam in the holder on the AIO controller, at the water's edge

Anti-spin for your underwater camera

Your camera, still in the water. An underwater camera hangs from its own cable and turns with every movement of the boat or the water. The anti-spin clips around the camera and keeps it still, at the angle you choose.

One clip decides where it looks

The cable loops to a clip on the curved arm; that clip becomes the pivot and the centre of gravity hangs straight below it. The fins then keep it still, even when the boat or the current pulls.

Fits your camera

Each anti-spin is designed for one camera model, measured to a tenth of a millimetre. Choose your model on Etsy.

Anti-spin on the Stealthcam UK Winchcam, seen from the front at an angle

Stealthcam UK Winchcam

Ø 34.12 mm, length 63 mm

Clips behind the edge where the camera gets narrower. Lens and lights stay clear.

Anti-spin on the Carplounge Winchcam, seen from the front at an angle

Carplounge Winchcam

Ø 30.05 mm, rim Ø 34

Clips behind the rim at the front. The holes around the camera stay open.

Anti-spin on Etsy

Different camera? Send me the diameter, the length, the cable thickness and a photo via Etsy and I'll see if I can make one.

Parts for your Carplounge bait boat

Battery handles for the RT4 and RT7, and a sonar cover made for the RT7. Both measured against the original.

Two Carplounge Smart batteries with the black replacement handle raised as a carrying grip

Battery handles for the Smart battery

RT4 and RT7 Smart battery, set of 2 or 4

The original handles often break after a while. These are reinforced at the weak points and fit straight in place of the original.

Battery handles on Etsy

Black sonar cover flush in the sonar recess of a Carplounge RT7 bait boat hull, seen from above

Sonar cover for the Carplounge RT7

Carplounge RT7 only

Made specifically for the hull of the RT7. If you use the built-in fish finder, the original sonar recess stays open. This cover seals it flush with the hull, for less drag in the water. No drilling.

Sonar cover on Etsy

Also in the works

For the Carplounge bait boat and the RT7 remote, the All-in-One controller (AIO) with screen.

  • Handle clamp for the Winchcam

    Clips onto the handle of your bait boat; the camera clips into the front. No screws.

    Slot 19.60 mm

    Coming soon

  • Sun hood for the RT7 controller

    Clips over the edge of the screen and keeps it readable in the sun. Folds flat to fit in your bag.

    Frame 188 mm

    Coming soon

Buy

Ordering, payment and shipping all go through Etsy. You can ask questions there too.

FAQ

Will it fit my gear?

Every product is designed for one model and measured against the original. If your boat, controller, monitor or camera isn't listed, send me the measurements and a photo via Etsy and I'll see if I can make one.

Does the sonar cover also fit the RT4?

No, the sonar cover is made specifically for the hull of the Carplounge RT7. The battery handles do fit the Smart batteries of both the RT4 and the RT7.

Can it handle water and sun?

Yes, everything is water and UV resistant and can stay outdoors all season.

How do I take the monitor holder off the controller?

Pull the two tabs at the bottom of the clip arms outwards and lift the screen holder off. The frame can simply stay on the controller.

Why does an underwater camera spin?

The camera hangs from its own cable. That cable twists with every movement of the boat or the water, and the camera turns with it. The fins of the anti-spin work like a weather vane and keep it still.

How do I get the anti-spin off again?

Bend the four clip fingers slightly outwards and slide the camera out.